Toilet Replacement
Toilet Replacement Bonita Springs FL done right the first time
When your toilet rocks, leaks at the base, or runs all night, Toilet Replacement Bonita Springs FL is the fix that ends the problem for good. We pull the old bowl, inspect the flange and subfloor, set a new comfort height toilet, and test every connection before we leave. Homeowners in Bonita Bay, Pelican Landing, and Spanish Wells call us because we show up on time and clean up after ourselves.
Service overview
What Toilet Replacement Bonita Springs FL actually involves
A proper toilet replacement is more than swapping one bowl for another. We shut off the supply, drain the tank, and lift the old fixture without scratching the floor. Then we inspect the closet flange for cracks, check the subfloor for soft spots, and replace the wax ring and closet bolts. A new quarter-turn shutoff valve goes on if yours is seized. We set the new toilet level, torque the bolts evenly, and run three full flush cycles to confirm no leaks at the base or supply line.
Most Bonita Springs homes we service were built between the 1980s and early 2000s, so original toilets are often 1.6 gpf models with worn flappers and mineral-crusted fill valves. Hard water from the local aquifer leaves scale inside the tank and bowl, and that buildup is why so many units run constantly or refill slowly. If your toilet is more than 15 years old, a new toilet installation Bonita Springs FL is usually cheaper than chasing parts on a fixture that is already past its service life.
Practical benefits
Why homeowners upgrade their toilets
A new toilet is one of the few bathroom projects that pays you back every single day, in water savings, fewer clogs, and a bathroom that finally looks finished.
Lower water bills
Modern 1.28 gpf and dual-flush models use up to 20 percent less water than the 1.6 gpf toilets common in older Bonita Springs homes. For a family of four, that is roughly 4,000 gallons saved per year. We size the flush volume to your household so you are not paying for water you never needed.
Fewer clogs and backups
Older toilets with worn siphon jets and scaled trapways clog constantly. A new American Standard or Toto model with a fully glazed 2-inch trapway moves waste through with a single flush. If you have been keeping a plunger next to the bowl, that habit ends the day we install.
Comfort height seating
Standard toilets sit at 15 inches; comfort height models sit at 17 to 19 inches, which is easier on knees and hips. We install comfort height toilet installation Bonita Springs, Florida homeowners ask for by name, especially in primary bathrooms and any home where an older adult lives or visits.
A cleaner, drier floor
A failing wax ring lets sewer gas and moisture escape at the base, which stains tile and feeds mold in Florida humidity. We replace the ring, reseal the base with silicone sealant, and check the flange height so the new toilet sits flat. No rocking, no odor, no water wicking under the tile.
How service works
How our toilet replacement process works
Five steps, one visit for most jobs, and a clear picture of what happens from the moment we knock on your door until the new toilet is flushing clean.
STEP 01
Phone assessment
Call 512 325 0295 and tell us what the old toilet is doing, running, leaking, rocking, or clogging. We ask about the flange, the floor, and whether you have already picked a model. Most calls take five minutes and end with a scheduled window, often same-day.
Tools and methods
Tools and methods we use
Pipe wrench and adjustable wrench
Used to break loose supply lines and closet nuts without rounding the fittings. We keep both sizes on the truck so we are not improvising with pliers on a seized connection.
Moisture meter
Checks the subfloor around the flange for hidden water damage before we set a new toilet. A dry reading means we can install; a wet reading means we quote a subfloor repair first.
Laser level
Confirms the new toilet sits level front-to-back and side-to-side. A level toilet seals evenly at the base and does not rock, which protects the wax ring.
Caulking gun and silicone sealant
Applies a clean bead of silicone sealant around the base after installation. Silicone resists bathroom moisture better than latex caulk and stays flexible for years.
Shop vacuum
Cleans up water, wax residue, and debris during the swap. We vacuum the flange area before setting the new toilet so the seal sits on a clean surface.
Plumber's snake
Clears minor clogs in the branch line while the toilet is off. If the drain is slow with the toilet removed, we run the snake before installing the new fixture.
Oscillating multi-tool
Cuts closet bolts, trims flange spacers, and handles tight cuts around the flange without damaging tile. It is the tool that saves a floor when a bolt is seized.
Florida Building Code compliance
Every install follows Florida Building Code and the ICC Residential Building Code (IRC) for flange height, water supply, and venting. We confirm the rough-in measurement matches the new toilet before setting it, and we pull permits when the scope requires one.
ANSI A118.10 waterproofing standard
When the toilet replacement is part of a larger bathroom project, we follow ANSI A118.10 for waterproofing membrane installation around the wet area. That standard keeps moisture from reaching the subfloor and the flange.
EPA Lead-Safe work practices
For homes built before 1978, we follow EPA Lead-Safe Certified Firm procedures when disturbing painted surfaces. That includes containment, cleanup verification, and proper disposal of debris.
Flange height verification
We measure the closet flange against the finished floor before setting the toilet. A flange that sits too low gets a spacer; one that sits too high gets a different wax ring. Getting this right is what prevents leaks at the base.
Where this service fits
When to schedule a toilet replacement
Your toilet is 15 years or older and parts are getting hard to find.
We replace the toilet with a current model that uses standard parts available at any supplier. We match the rough-in measurement and bowl shape to your existing setup so no floor or wall changes are needed. A reliable toilet with parts you can buy locally, installed in under two hours, with a one-year workmanship warranty.
You are remodeling the bathroom and want the toilet to match new fixtures.
We coordinate the toilet replacement with your vanity, flooring, and shower work so the finishes match. We can set the toilet last, after tile and grout cure, to avoid damage during the rest of the remodel. A finished bathroom where the toilet, vanity, and tile look like they were specified together, not pieced in over time.
An aging parent or frequent guest needs a taller, easier-to-use toilet.
We install a comfort height toilet at 17 to 19 inches, with an elongated bowl and a soft-close seat. If needed, we add grab bars nearby and confirm the layout meets ADA Accessibility Guidelines for clearance. A safer bathroom that is easier to use, with a toilet that matches the height of the vanity and reduces strain on knees and hips.
You are selling the home and the inspection flagged a running or leaking toilet.
We handle the replacement fast, document the work, and provide a receipt for the buyer. If the flange or subfloor needs repair, we photograph the fix so there are no questions at closing. A clean inspection report, a working toilet, and paperwork you can hand to the buyer or their agent without delay.
Local execution
How toilet replacement runs in Bonita Springs
Bonita Springs sits on the Gulf coast, and that shapes every toilet job we do. Indoor humidity stays high most of the year, so a leaking wax ring does not just stain the floor, it feeds mold within days. Hard water from the local aquifer leaves scale inside tanks and trapways, which is why so many 1990s and early-2000s toilets in Bonita Bay and Pelican Landing run constantly or refill slowly. We size the new toilet to the household and confirm the shutoff works, because a seized valve turns a one-hour job into a water cleanup. If you are comparing toilet replacement Bonita Springs FL cost, remember that a same-day swap is almost always cheaper than a subfloor repair. We also handle toilet replacement in Bonita National Bonita Springs FL and The Brooks, where HOA rules sometimes require specific fixture finishes. Newer construction in 34134 often has PVC flanges at the right height, while older villas near the Imperial River sometimes need flange repair before the new toilet goes down.
Bonita Bay
Many homes here have original 1990s toilets with worn flappers. HOA guidelines may require neutral finishes, which we match with Kohler and American Standard models.
Pelican Landing
Villas and single-family homes with PVC flanges at standard height. Most swaps are same-day, and we often pair them with bathroom ventilation upgrades.
Spanish Wells
Older homes where cast iron or brass flanges may need repair. We keep flange spacers and repair rings on the truck for these jobs.
Bonita National
Newer construction with comfort height toilets already common. Replacements here are usually upgrades to dual-flush or quieter fill valves.
The Brooks
Larger homes with multiple bathrooms. We schedule multi-toilet replacements in one visit to save on labor and disruption.
Year-round high humidity
A failed wax ring lets moisture escape at the base, and mold can appear within 48 hours. We use silicone sealant and confirm a dry subfloor before caulking.
Hard water from the local aquifer
Scale builds up inside tanks and trapways, weakening the flush. We recommend fully glazed trapways and check supply pressure during the install.
Older housing stock with cast iron flanges
Flanges in 1970s and 1980s homes may be cracked or set below the finished floor. We inspect and repair before setting the new toilet.
HOA finish requirements
Some Bonita Springs communities require specific fixture colors or finishes. We confirm the model meets HOA rules before ordering.
Problems we solve
Toilet problems we fix in Bonita Springs
Most toilet calls come down to one of a handful of failures. Here is what we see most often in Bonita Springs homes and how we fix it.
Toilet runs constantly after replacement
We adjust the fill valve height, check the flapper seal, and confirm the refill tube is not siphoning. If the new toilet is running, it is almost always a valve adjustment or a flapper that needs reseating. We fix it on the spot under warranty. A running toilet can waste 200 gallons a day and add $30 to $70 a month to your water bill. It also wears out the fill valve and can overflow if the flapper sticks open.
Water pooling at the base of the toilet
We pull the toilet, inspect the flange, and replace the wax ring. If the flange is cracked, we repair or replace it before setting the new toilet. A moisture meter check confirms the subfloor is dry before we caulk the base. Water at the base means the wax ring has failed or the flange is cracked. Left alone, it rots the subfloor, stains tile, and feeds mold in Florida humidity. A small leak becomes a $1,500 floor repair fast.
Toilet rocks or wobbles when you sit
We set the new toilet with shims and a flange spacer if needed, then caulk the base to lock it in place. If the subfloor is soft, we patch it with pressure-treated lumber before installing. No rocking, no seal stress. A rocking toilet stresses the wax ring and breaks the seal. It usually means the flange is above or below the finished floor, or the subfloor has softened from a slow leak. Ignoring it leads to a full floor repair.
Hard water scale and weak flush
A new toilet with a fully glazed trapway solves the problem at the source. We recommend 1.28 gpf models with wide trapways that resist scale buildup. We also check your water pressure and shutoff while we are there. Bonita Springs water leaves mineral scale inside the tank and trapway. Over time the flush weakens, clogs increase, and the toilet never fully clears the bowl. Cleaning products only reach the surface.
A practical standard for every visit.
Clear planningPrepared arrivalsCareful workLocal follow-through
Experience in the details
Toilet replacement expertise you can verify
Our installers work on toilets every week across Bonita Springs and Lee County, from 1980s villas in Spanish Wells to newer builds in Bonita National. We hold a Florida Certified Residential Contractor (CRC) license and follow the Florida Building Code and ICC Residential Building Code (IRC) on every job. That means flange height, closet bolt spacing, and supply line sizing are done to spec, not guessed. We also carry EPA Lead-Safe Certified Firm status for pre-1978 homes, which matters in older Bonita Springs neighborhoods.
- Florida Certified Residential Contractor (CRC) license held by the owner
- EPA Lead-Safe Certified Firm for pre-1978 homes in Lee County
- Comfort height and ADA-compliant installs available on request
- Flange repair and subfloor patching handled in-house, no subs
- Same-day service across Bonita Springs, FL and surrounding ZIP codes
Where we work
One local team. A lot of ground covered.
Downtown Bonita SpringsBonita Springs City CenterBonita BayPelican LandingPelican MarshSpanish WellsImperial RiverBonita NationalVanderbilt BeachBarefoot BeachBonita BeachCoconut Point
Check my address Most toilet replacements in Bonita Springs run $250 to $650 in 2026, including labor, wax ring, closet bolts, supply line, and haul-away. The toilet itself adds $150 to $800 depending on brand and features. Comfort height models and dual-flush units sit at the higher end. Flange repair or subfloor patching adds $100 to $400 if we find damage once the old toilet is up.
A standard toilet installation takes 45 minutes to two hours. If the flange is cracked, the shutoff valve is seized, or the subfloor needs patching, plan on two to four hours. We schedule a two-hour window and tell you upfront if the job is running long. Most Bonita Springs customers have a working toilet before lunch.
Look for a licensed Florida contractor who pulls permits when required and warranties the install. We hold a Florida Certified Residential Contractor (CRC) license, carry EPA Lead-Safe certification for older homes, and have installed toilets across Bonita Bay, Pelican Landing, and The Brooks. Ask any installer for their license number and warranty terms before you book.
A comfort height, 1.28 gpf elongated model with a fully glazed trapway handles Bonita Springs hard water best. Kohler, Toto, and American Standard all make units in that spec. Avoid one-piece designs with narrow trapways if you have a busy household. We stock the top sellers on the truck and can match the finish to your existing fixtures.
Keep exploring
Related Services
Your next step is waiting
Book Toilet Replacement Bonita Springs FL today
Call 512 325 0295 and we will give you a flat price over the phone, then schedule a same-day or next-day window. Licensed, insured, and warrantied work across Lee County. If your toilet is leaking, running, or rocking, we can stop it today.
Start with the basics
Get Your Free Bathroom Estimate
Call us at 512 325 0295 or send a message and we will get back to you the same business day. We answer the phone Monday through Friday, 8:00 to 6:00, and we book most estimates within the week. Tell us what is going on with your bathroom and we will tell you what it takes to fix it.